HABeR-XLWR low switchgear up to 6300A
HaBeR-XLWR - a switchgear system with a full TTA-type testing designed to supply power to industrial buildings, office, usable and public utility buildings, such as schools, hospitals, etc.
The HaBeR-XLWR system has been tested and certified in the Electrotechnical Institute in Warsaw against the requirements of the following standards:
- PN-EN-60439-1:2003+A1:2006
- PN-EN-61439-1/2:2011
- PN-EN-60526:2003
- PN-EN-50102:2001
Features:
- insulation class: I (first)
- rated voltage of insulation Ui: up to 1000V AC/1200V DC
- rated operational voltage Ue: up to 690V AC/500V DC
- operating rated voltage: 400V
- Rated AC: 65kA
- arc burning time: 100 ms
- permissible operating temperature: -5°C to +40°C,
the mean value of 24 hours: + 35°C - nominal frequency: 50/60 Hz
- rated 1s short-time withstand current Icw: from 50kA to 105kA
- rated peak withstand current Ipk: from 105kA to 231kA
- rated impulse withstand voltage Uimp: up to 12 kV
- rated low frequency withstand voltage: up to 3.5 kV
- overvoltage category: IV
- degree of pollution: 3
- IP rating: IP31/30, IP43/30 and IP54/30
- a form of internal division: 4b do 2b
- height without base: 2200 mm + 50 mm base
- depth (in the body): 600/800/1000 mm
Protection against mechanical damage:
- for solid doors IK10
- for transparent door IK08
Rated continuous current for busbars:
- for IP31/30 Izn: from 630A to 6300A
- for IP43/30 Izn: from 630A to 5500A
- for IP54/30 Izn: from 630A to 5000A
- additional - optional - degree of protection against the possibility of internal short circuit through insulation of busbars and the system of horizontal and vertical insulating barriers of the main bridge
- protection of persons in the event of a short circuit according to IEC 61641
- width: 400/450/600/800 or 400+400/1000 or 600+400/1200 or 600+800/1400 mm
- positioning: wall mounted, freestanding; back to back
- input/output - of cables and busbar trunking: upper, lower cable compartment
System tested with equipment of leading manufacturers:
EATON Moeller, Siemens, Schneider, ABB, Legrand, Efen, Jean Muller, Socomec.
System review
The HaBeR-XLWR is designed for freestanding, wall-mounted or back-to-back installation, with support for single-sided Single Front and double-sided Double Front
1. Ingoing or outgoing feeder bay of P type
- ingoing, outgoing or sectional feeder bay up to 6300A
- fixed or movable switches, 3- or 4-pole junction
- operating voltage up to 690V AC
- bay widths: 400/425/600/800/1000/1200 mm
- connection from the top or bottom (for cables, busbars or traditional rail bridges)
- enclosed functional compartments: power, devices, measuring
2. Ingoing feeder bays with slat fuse switch disconnectors type FV, FH, FHV
- outgoing feeder bays with one or two compartments adjusted for mounting
- vertical slat fuse switch disconnectors of class NSL 1-4a to 1600A
- horizontal slat fuse switch disconnectors of class NSL 00 to 160A - configuration out of respective blocks of instruments adapted to the mechanical, electrical or thermal capacity of each bay
- bay width: 400/600/800 mm or 600+400mm/600+600mm
- cable connection from the top or bottom for vertical switches and for cable compartment for horizontal switches
- outgoing feeder bays with one or two compartments adjusted for mounting
- vertical slat fuse switch disconnectors of class SASIL00-SASIL3 (160A - 630A) - configuration of the respective blocks of instruments adapted to capacity:
- mechanical, electrical and thermal of each bay - bay width: 400/600/800 mm or 600+400mm/600+600mm
- top or bottom cable connection
3. Ingoing feeder bays with slat fuse switch disconnectors with snap-action mechanism type FVR, FHR
- outgoing feeder bays with one or two compartments adjusted
or mounting vertical slat fuse switch disconnectors of class SASIL00-SASIL3
(160A - 630A) - configuration of the respective blocks of instruments adapted to capacity:
- mechanical, electrical and thermal of each bay - bay width: 400/600/800 mm or 600+400 mm/600+600 mm
- top or bottom cable connection
4. Incoming feeder bays with circuit breakers/disconnectors MCCB
type MV, MV, MV, MFH
- outgoing feeder bays with one or two compartments adjusted
for mounting vertical slat fuse switch disconnectors of class NSL 1-4a do 1600A
- horizontal slat fuse disconnectors of class NSL 00 to 160A - configuration of the respective blocks of instruments adapted to capacity:
- mechanical, electrical and thermal of each bay - bay width: 400/600/800 mm or 400+400/600+400/600+600 mm
- cable connection from the top or bottom for vertical disconnectors
and for cable compartment for horizontal disconnectors
5. Incoming feeder bays with retractable cartridges type W and MCC
- outgoing feeder bays with one or two compartments adjusted
for mounting disconnectors or switches - all cartridges can be equipped with intelligent systems based on a system
of electronic security and control of SIMOCODE class and can be optionally
equipped with continuous temperature monitoring input contacts,
output contacts and the inside of the cartridge. - power for the cartridge type MCC: linear reception from 63A to 630A;
motor drive from 15kW to 200kW - power for the cartridge type W: linear reception from 25A to 630A;
motor drive from 11kW to 250kW - bay width: 600+400 (200 for back cable outputs) or 600+600 mm
- cable connection: ODK - bottom cable output,
OGK - upper cable output (for cartridges of type MCC) - cable connections to the lateral or back cable compartment
(for cartridges of type W)
6. Incoming feeder bays in a plug-in or fixed version of MCR type
- two-compartment bays for mounting of the control blocks or power supply
of lines in the male version - top or bottom cable connection
- bay width: 600+400 mm or 600+600 mm
7. Incoming feeder bays for individual configuration of G1 and G2 type
- empty bays of general purpose for building control systems, inverters,
soft starters, special power supply systems, installation equipment, etc. - the size of the assembly module 50 mm
- according to individual requirements
- typical bays of standard widths: 400/600/800/400+400/600+600 mm
8. Bays for capacitor batteries of BKn and BKs type
- bays for reactive power compensation without reactors, reinforced,
with reactors 7% and 14% - freestanding objects - bays with a width of 600/800 mm and multiples
of these bays; reactive power up to 300kvar per one bridge in one cabinet - serial objects in a switchgear - bays with a width of 600/800 mm and multiples
of these bays; at the power supply of each bay of the battery - fuse switch NT3
or compact circuit of NT3 class; reactive power up to 250kvar per one bridge
in one cabinet - compensating blocks built as panels
9. Corner bays
- unicompartimental bays are designed to connect bays of switchgears
in rooms with small dimensions and set these bays perpendicularly - switchgears can be set in the shape of “L” or “U”
- bays with a width of: 650/850/1050 mm depth of 650/850/1050 mm
- the main bridge carried in the bottom part of the cabinet (MGD),
in the upper part (MGG) or at both levels